XBD20A

Mã sản phẩm:

Chúng tôi là nhà phân phối chính thức các sản phẩm của Spgmotor tại thị trường Việt Nam, Quý khách có nhu cầu về các sản phẩm của spgmotor vui lòng liên hệ trực tiếp với chúng tôi để được tư vấn nhanh hơn.

Hotline: 0974190088/Zalo

Email: vuonguoc@gmail.com

Giá: Liên hệ

MÔ TẢ SẢN PHẨM

XBD20A

20W 100~120V BLDC DRIVER

Specification

Title

Combi type

XBA-620A-□

XBA-620B-□

XBA-620U-□

Gear type

XLM620G

D-Cut type

XLM620D

Rated Output (continuous)

Rated Output
(continuous)

Voltage

Single Phase 100~120

Single Phase 200~230

Three Phase 200~230

Frequency

50/60

Rated Input Current

0.65

0.40

0.20

Maximum Input Current

1.30

0.90

0.50

Rated TORQUE

N·m(kgf·cm)

0.066(0.66)

Driving TORQUE

N·m(kgf·cm)

0.08(0.8)

Permissible Load
Inertia Moment

J kg·m2

1.5×10-⁴

GD2 kgf·㎠

Rated RPM

r/min

3,000

Speed Setting Range

r/min

200 to 3,000 (Speed Ratio 1:10)

Speed Variability Rate

Load

Less than ±1% (0 to rated torque, at rated speed)

Vlotage

Less than ±1% (supply voltage ±10%, at rated speed with no load)

Temperture

Less than ±1% (0 to +40℃ (+32 to +104℉), at rated speed with no load)


	※ For permissible load inertia in the geared motor, refer to Permissible Torque-Geared Motor [GD²]. ※ Enter the ratio in the box(□) model number. ※ The values for each item is for the motor only.

□ Commonalities

Category	Specifications
SLOW RUN / SLOW STOP	0.5 to 15 seconds (Applicable for both Slow Run and Slow Stop)
Speed Control	1. Built-in Potentiometer 2. External Potentiometer (20㏀ 1/4W) 3. External DC Voltage(0~5 Volt)
Input Signal	Photocoupler input method, input resistance: 2㏀, operates at DC 12V±10%, common for EXT., CW, and CCW
Output Signal	Opencollector output, external use conditions: Less than 26.4V 10mA, common for Speed Out and Alarm Out.
Protection Feature	If following protection functions are operated, control unit alarm signal is outputs and motor comes to stop. ㆍProtection for machine overload : When an overload that exceeds the motor’s rate touque has been continued for more than 5 seconds ㆍProtection for overvoltage : When the voltage permitted for the control unit has exceed specified voltage ㆍProtectionguard for image formation : When malfunction occures in the motor feedback signals due to cables disconnection and connector disconnection. ㆍProtection for undervoltage : When the voltage permitted at the control unit has shortage of more than specified voltage ㆍ Protection for over speeding : When the speed of the motor exceed 3800r/min
Motor Insulation Level	Class E (120℃)
Time Rating	Continuous

□ General Specs

Item	MOTOR	CONTROL UNIT
Dielectric strength	If applying 60HZ 1,500V between the coil and the case for 1 minute after continuous operating under normal temperature and humidity conditions, any fault is not occurred	Sufficient to withstand 3.0kV at 50Hz applied between power supply terminal (I/O terminal) And I/O terminals for 1 minutes, and 1.5kV at 50Hz applied between protective earth terminal and power supply terminals
Insulation Resistance	After continuous operating under normal temperature and humidity conditions, if measured the resistance value between the coil and the case using DC500V Mega Tester, should be over 100㏁.	If the resistance value between protection ground terminal and power input is measured using DC500V Mega Tester, should be over 100㏁.
Ambient Temperature	℃ to +40℃(＋32℉ to ＋104℉) (nofreezing)	0℃ to +50℃(＋32℉ to ＋122℉) (nofreezing)
Ambient Humidity	Less then 85% (no dew condensation)
Ambience	Nocorroive gas or dust
Protection Class	IP65 (excluding the output shaft side)	IP10

※ Caution: Use it, ensuring that surface temperature of motor does not exceed over 90℃.

□ Permissible Torque-Geared Motor [GD²]

Title	Speed Setting Range [r/min]	60~600	30~300	20~200	15~150	10~100	6~60	3~30	1.5~15
Title	Gear Ratio	5	10	15	20	30	50	100	200
XBA620( )-□K		0.29 2.9	0.59 5.9	0.88 8.8	1.2 12	1.7 17	2.8 28	5.6 56	200 60

※ ( ) of item name represents voltage specification
※ □ of item name represents the reduction ratio.
※ Rotation direction is the same direction of additional motor marked in the ▩, others is reverse direction.

□ Permissible Load Inertia[J]- Geared Motor

Model	Gear Ratio	5	10	15	20	30	50	100	200
XBA620( )-□K	General run	1.2×10-³ 50	5×10-³ 200	11×10-³ 450	20×10-³ 800	37×10-³ 1.5×10³	92×10-³ 3.7×10³	0.25 10×10³	0.5 20×10³
XBA620( )-□K	Instant stop, run	0.15×10-³ 6.25	0.62×10-³ 25	1.4×10-³ 56	2.5×10-³ 100	5.6×10-³ 225	15.6×10-³ 625	15.6×10-³ 625	15.6×10-³ 625

※ ( ) of item name represents voltage specification
※ □ of indicates deceleration ratio.

□ Permissible Overhand Load and Permissible Thrust Load

Model		Gear Ratio	Permissible Overhand Load				Permissible Thrust Load
			10mm(0.3937 in) from end of the output shaft.		20mm(0.7874 in) from end of the output shaft.
			N	kgf	N	kgf	N	kgf
Geared Motor	XBA620( )-□K	5	100	10	150	15	40	4
		10~20	150	15	200	20
		30~200	200	20	300	30
Motor	XBM620D		87.2	8.72	107	10.7