XBU840GU
40W 삼상 200~2300V Frange Size 80 X 80 mm Gear Type + XBD40A Control Unit
| Specification |
| Title |
Combi type |
XBA-620A-□ |
XBA-620B-□ |
XBA-620U-□ |
| Gear type |
XLM620G |
| D-Cut type |
XLM620D |
| Rated Output (continuous) |
W |
|
20 |
Rated Output
(continuous) |
|
Single Phase 100~120 |
Single Phase 200~230 |
Three Phase 200~230 |
|
|
50/60 |
|
|
0.65 |
0.40 |
0.20 |
|
|
1.30 |
0.90 |
0.50 |
| Rated TORQUE |
N·m(kgf·cm) |
0.066(0.66) |
| Driving TORQUE |
N·m(kgf·cm) |
0.08(0.8) |
Permissible Load
Inertia Moment |
J kg·m2 |
1.5×10-⁴ |
| GD2 kgf·㎠ |
6 |
| Rated RPM |
r/min |
3,000 |
| Speed Setting Range |
r/min |
200 to 3,000 (Speed Ratio 1:10) |
| Speed Variability Rate |
Load |
Less than ±1% (0 to rated torque, at rated speed) |
| Vlotage |
Less than ±1% (supply voltage ±10%, at rated speed with no load) |
| Temperture |
Less than ±1% (0 to +40℃ (+32 to +104℉), at rated speed with no load) |
|
|
|
|
|
※ For permissible load inertia in the geared motor, refer to Permissible Torque-Geared Motor [GD²].
※ Enter the ratio in the box(□) model number.
※ The values for each item is for the motor only. |
|
|
|
|
| □ Commonalities |
| Category |
Specifications |
| SLOW RUN / SLOW STOP |
0.5 to 15 seconds (Applicable for both Slow Run and Slow Stop) |
| Speed Control |
1. Built-in Potentiometer 2. External Potentiometer (20㏀ 1/4W) 3. External DC Voltage(0~5 Volt) |
| Input Signal |
Photocoupler input method, input resistance: 2㏀, operates at DC 12V±10%, common for EXT., CW, and CCW |
| Output Signal |
Opencollector output, external use conditions: Less than 26.4V 10mA, common for Speed Out and Alarm Out. |
| Protection Feature |
If following protection functions are operated, control unit alarm signal is outputs and motor comes to stop.
ㆍProtection for machine overload : When an overload that exceeds the motor’s rate touque has been continued for more than 5 seconds
ㆍProtection for overvoltage : When the voltage permitted for the control unit has exceed specified voltage
ㆍProtectionguard for image formation : When malfunction occures in the motor feedback signals due to cables disconnection and connector disconnection.
ㆍProtection for undervoltage : When the voltage permitted at the control unit has shortage of more than specified voltage
ㆍ Protection for over speeding : When the speed of the motor exceed 3800r/min |
| Motor Insulation Level |
Class E (120℃) |
| Time Rating |
Continuous |
|
|
| □ General Specs |
| Item |
MOTOR |
CONTROL UNIT |
| Dielectric strength |
If applying 60HZ 1,500V between the coil and the case for 1 minute after continuous operating under normal temperature and humidity conditions, any fault is not occurred |
Sufficient to withstand 3.0kV at 50Hz applied between power supply terminal (I/O terminal) And I/O terminals for 1 minutes, and 1.5kV at 50Hz applied between protective earth terminal and power supply terminals |
| Insulation Resistance |
After continuous operating under normal temperature and humidity conditions, if measured the resistance value between the coil and the case using DC500V Mega Tester, should be over 100㏁. |
If the resistance value between protection ground terminal and power input is measured using DC500V Mega Tester, should be over 100㏁. |
| Ambient Temperature |
℃ to +40℃(＋32℉ to ＋104℉) (nofreezing) |
0℃ to +50℃(＋32℉ to ＋122℉) (nofreezing) |
| Ambient Humidity |
Less then 85% (no dew condensation) |
| Ambience |
Nocorroive gas or dust |
| Protection Class |
IP65 (excluding the output shaft side) |
IP10 |
|
※ Caution: Use it, ensuring that surface temperature of motor does not exceed over 90℃. |
|
| □ Permissible Torque-Geared Motor [GD²] |
| Title |
Speed Setting Range [r/min] |
60~600 |
30~300 |
20~200 |
15~150 |
10~100 |
6~60 |
3~30 |
1.5~15 |
| Gear Ratio |
5 |
10 |
15 |
20 |
30 |
50 |
100 |
200 |
| XBA620( )-□K |
0.29
2.9 |
0.59
5.9 |
0.88
8.8 |
1.2
12 |
1.7
17 |
2.8
28 |
5.6
56 |
200
60 |
|
|
※ ( ) of item name represents voltage specification
※ □ of item name represents the reduction ratio.
※ Rotation direction is the same direction of additional motor marked in the ▩, others is reverse direction. |
|
| □ Permissible Load Inertia[J]- Geared Motor |
| Model |
Gear Ratio |
5 |
10 |
15 |
20 |
30 |
50 |
100 |
200 |
| XBA620( )-□K |
General run |
1.2×10-³
50 |
5×10-³
200 |
11×10-³
450 |
20×10-³
800 |
37×10-³
1.5×10³ |
92×10-³
3.7×10³ |
0.25
10×10³ |
0.5
20×10³ |
| Instant stop, run |
0.15×10-³
6.25 |
0.62×10-³
25 |
1.4×10-³
56 |
2.5×10-³
100 |
5.6×10-³
225 |
15.6×10-³
625 |
15.6×10-³
625 |
15.6×10-³
625 |
|
|
※ ( ) of item name represents voltage specification
※ □ of indicates deceleration ratio. |
|
| □ Permissible Overhand Load and Permissible Thrust Load |
| Model |
Gear Ratio |
Permissible Overhand Load |
Permissible Thrust Load |
| 10mm(0.3937 in) from end of the output shaft. |
20mm(0.7874 in) from end of the output shaft. |
| N |
kgf |
N |
kgf |
N |
kgf |
| Geared Motor |
XBA620( )-□K |
5 |
100 |
10 |
150 |
15 |
40 |
4 |
| 10~20 |
150 |
15 |
200 |
20 |
| 30~200 |
200 |
20 |
300 |
30 |
| Motor |
XBM620D |
87.2 |
8.72 |
107 |
10.7 |
|
|
※ ( ) of item name represents voltage specification
※ □ indicates deceleration ratio. |
Do not engage the thrust load. If unavoidable, engage below 50 % of motor weight. |
|
| □ RPM – Torque Feature |
| XBU620G( ) / XBU620D( ) |
|
|
|
XWM940D,XWM940D, XWM940G, XWM940G, XWD40A, XWD40B, XWU940GA, XWU940GB, XWU940DA, XWU940DB, XBU620DA, XBU620DB, XBU620DUB, XBU620GA,
XBU620GB, XBU620GU, XBU840DA, XBU849DB, XBU849DU, XBU840GA, XBU840GB, XBU840GU, XBU975DA, XBU975DB, XBU975DU, XBU975GA, XBU975GB, XBU975GU,
XBU9120DA, XBU9120DB, XBU9120DU, XBU9120GA, XBU9120GB, XBM9120GU, XBU9150DA, XBU9150DB, XBU9150DU, XQM630D, XQM630G, XQM860D, XQM860G,
XQM975D, XQM975G, XQM9120D, XQM9120G, XQU630DB, XQU630DU, XQU630GU, XQU630GB, XQU860DB, XQU860DU, XQU860GB, XQU860GU, XQU975DB, XQU975DU,
XQU975GB, XQU975GU, XQU9120DB, XQU9120DU, XQU9120GB, XQU9120GU, XQD30B, XQD30U, XQD60B, XQD60U, XQD97B, XQD75U, XFD30, XFD50, XFD100, XFM630D,
XFM630G, XFM850D, XFM850G, XFM9100D, XFM9100G, XFU630D, XFU630G, XFU850D, XFU850G, XFU9100D, XFU9100G, XQU630GB, XQU860DB, XQU860DU,
XQU860GB, XQU860GU, XQU975DB, XQU975DU, XQU975GB, XQU975GU, XQU9120DB, XQU9120DU, XQU9120GB, XQU9120GU, XQD30B, XQD30U, XFD30, XFD50, XFD100,
XFM630D, XFM630G, XFM850D, XFM850G, XFM9100D, XFM9100G, XFU630D, XFU630G, XFU850D, XFU850G, XFU9100D, XFU9100G, XQU630GB, XQU860DB, XQU860DU,
XQU860GB, XQU860GU, XQU975DB, XQU975DU, XQU975GB, XQU975GU, XQU9120DB, XQU9120DU, XQU9120GB, XQU9120GU, XQD30B, XQD30U, XQM630D, XQM630G,
XQM630G, XQM860D, XQM860G, XQM975D, XQM975G, XQM9120D, XQM9120G, XQU630DB, XQU630DU, XQU630GU, XQU630GB, XQU860DB, XQU860DU, XQU860GB,
XQU860GU, XQU975DB, XQU975DU, XQU975GB, XQU975GU, XQU9120DB, XQU9120DU, XQU9120GB, XQU9120GU, XQD30B, XQD30U, XQD60B, XQD60U, XQD97B, XQD75U, XBU840GU, XBU840GU, XBU840GU, XBU840GU, XBU840GU, XBU840GU, XBU840GU, XBU840GU,
